Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
We have discovered this article relating to Tools You Need to Install a New Bathtub directly below on the net and reckoned it made sense to relate it with you in this article.
Installing a tub isn't specifically brain surgery, however it does call for solid plumbing, woodworking, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately difficult task. If the old tub is conveniently obtainable, the project can relocate immediately; if you have to open up a wall to eliminate the old tub and also place the new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will require a helper to leave the old bathtub as well as set in the new one. Make certain you have qualified on your own for the work as well as are comfortable trying it. As opposed to hiring a service provider to take control of a halfway-completed project, it is far better to consider employing one prior to you begin. Chances are you may need a professional plumber to make tube connections.
This write-up will assist you set up a new bath tub in your restroom if you have actually already acquired a new bathtub and also do not need to alter the setup of your previous water system pipelines.
Your tools and material list must make up the following:
Removing Old Touches
If you require to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is separate the water. After doing so, activate the taps to drain pipes any water remaining in the system. The process of removing the existing taps can be rather troublesome due to the restricted access that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. When the supply pipes have been eliminated, utilize the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary faucets from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the brand-new faucets, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to stop damage to the string. One end of the connector fits on the plastic tail of the faucet and also the other end provides a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the mounting opening in the bath/basin making certain that the washing machines remain in place in between the tap as well as the sink. Safeguard the tap in place with the maker given backnut. Once the faucet is securely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap connectors. The former type should be connected to the tap finishes first, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Installing the Tub
Utilizing both wooden boards under its feet, place the bath tub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the tub over the area of the boards instead of concentrating all the weight onto four little points.
The following goal is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the tub till the level reviews degree.
To mount taps, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Switch on the supply of water as well as check all joints as well as brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as also inspect the overflow electrical outlet as well as the typical electrical outlet for leaks.
Ultimately, fix the bath paneling as described in the producer's instruction manual. Tiling as well as sealing around the tub needs to wait till the bath tub has actually been made use of a minimum of once as this will certainly resolve it right into its last setting.
Planning for the Setup
First of all, the supporting framework supplied with the bathroom needs to be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to avoid pressure on the bath tub.
Fit the flexible tap ports to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final setting.
Tiling Around the Bathtub
In the location where the bathroom fulfills the tile, it is needed to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to fracture a rigid seal, triggering the water to permeate the wall surface in between the bathroom as well as the tiling, bring about complications with moisture as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill the bath tub with water prior to securing, to allow for the motion experienced when the tub remains in usage. The sealer can split fairly very early if you do not take into consideration this activity before securing.
Alternatively, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are also easily readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic person who reads on A Step-by-Step Guide to Installing a Bathtub, I was thinking sharing that piece was worthwhile. Please take the time to distribute this article if you enjoyed it. Thanks for your time. Please pay a visit to our website back soon.
Plumbing emergencies? Our experts await. Report this page